
SAMSUNG LED
Model: UE49KU6650U
Panel: CY-VK049HGLV4V
LED backlight: EDGE LED
T-CON: integrated into MainBoard
LED driver (backlight): integrated into PSU
Power Supply (PSU): BN44-00876A L55E6_KHS
MainBoard: BN41-02528A BN94-11055C
IC MainBoard: SDP1531, K4F8E304HBMGCH, 25Q40CLSIP, 25Q80DVSIG, S24C512C
Tuner: BN40-00323A
Control: Wi-Fi: WCK730B
Technical Specifications UE49KU6650U
SAMSUNG UE49KU6650U
General repair guidelines for TV LCD LED
Possible manifestations of defects
- SAMSUNG UE49KU6650U TV does not turn on. There are no signs of operability. The indicators on the front panel do not light or flash, the TV does not respond to the remote control and control buttons.
With similar manifestations, in some cases, the BN44-00876A power module is faulty. It is necessary to measure its output voltages, and in case of their absence, check the operability of the power switches of the converters and rectifier diodes for the probability of a short circuit.
In case of breakdowns of semiconductors in the secondary circuits, the converter can usually work abnormally in the short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse often breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM microcircuits are usually checked by replacement with new ones, or obviously working.
- There is no image, but there is sound, it reacts to the remote control. Or the image appears when you turn it on and immediately disappears
The most likely in these cases is a malfunction of the LED backlight. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To check the health in the LED circuit, it is better to use a current source with a maximum voltage of 200V. We do not recommend using any voltage sources for this purpose. You can check each LED individually with a simple Chinese multimeter (powered by 9 volts) in the P-N-junction test mode. If you connect the red probe of the multimeter to the anode of the LED, and the black to its cathode, then the 3-volt LED will light up slightly, and in the opposite direction you can detect the transition of the emergency zener diode. A zener diode PN junction indirectly indicates a LED-a
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals standby mode.
Repair or diagnostics of the BN41-02528A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Often, the MB (SSB) card must be replaced in case of complex malfunctions that are difficult to detect. When trying to repair, you should check its elements - SDP1531, K4F8E304HBMGCH, 25Q40CLSIP, 25Q80DVSIG, S24C512C and replace failed chips with new ones. Some malfunctions may be due to the use of BGA soldering technologies in modern Main Board technologies. Typically, such defects are detected by local heating of the chip.
The malfunction of the tuner BN40-00323A is established after checking the software and all supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
It should be remembered! Attempts to independently repair the SAMSUNG UE49KU6650U TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-repairability of the device!


BN41-02528A
BN41-02528A can be used in TVs:
SAMSUNG UE43KU6650U (Panel CY-VK043HGAV5V), SAMSUNG UE43KU6000W UE43KU6000 (Panel CY-GK043HGEV1H), SAMSUNG UE55KU6400 UE55KU6400U (Panel CY-KK055HQLV4H), SAMSUNG UE49KU6670 UE49KU6670U (Panel CY-VK049HGLV4V), SAMSUNG UE40KU6000U (Panel LSF400FN05-L03 CY-GK040HGLV4V), SAMSUNG UE40KU6300U (Panel CY-WK040HGLV1V), SAMSUNG UE43KU6500U (Panel CY-VK043HGAV4V T430QVR01.0), SAMSUNG UE40KU6402U (Panel CY-KK040HGNV4H).
The appearance of the power supply
Main features of the SAMSUNG UE49KU6650U device:
Installed matrix (LED panel) CY-VK049HGLV4V.
The matrix control uses the Timing Controller (T-CON) integrated.
To power the backlight LEDs, a converter is used, combined with a power supply.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE49KU6650U TV is carried out by the power module BN44-00876A, or its analogues.
MainBoard - the main board (motherboard) is a BN41-02528A module, using microchips SDP1531, K4F8E304HBMGCH, 25Q40CLSIP, 25Q80DVSIG, S24C512C and others.
The tuner BN40-00323A provides the reception of television programs and tuning to channels.