
SAMSUNG LED
Model: UE49MU6500U
Chassis / Version: FF06
Panel: CY-VK049HGLV4V
LED backlight: LM41-00247A
LED driver (backlight): integrated into PSU
Power Supply (PSU): BN44-00876D REV1.1 L55E6R_KHS
PWM Power: PFC, PWM
MOSFET Power: N-FET TO-220F
MainBoard: BN41-02528A BN94-10784A
IC MainBoard: SDP1531, K4F8E304HBMGCH, 25Q40CLSIP, 25Q80DVSIG, S24C512C
Tuner: BN40-00323A
Technical Specifications UE49MU6500U
SAMSUNG UE49MU6500U
General repair guidelines for TV LCD LED
Possible malfunctions
- The SAMSUNG UE49MU6500U TV does not turn on, does not respond to the remote control and the control panel buttons, does not light up or blink indicators.
In such cases, the BN44-00876D power supply is usually faulty. It is necessary to measure its output voltages, and in case of their absence, check the serviceability of power switches (N-FET TO-220F) of converters and rectifier diodes for a short circuit probability.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during short circuit in the elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet power switches, used in switching power supplies, sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible parameters of the switch. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PFC, PWM PWM controllers, in the absence of visible damage or explicit short-circuit between the terminals, are checked by replacing with new ones, or obviously working.
- There is no image, but there is sound and reaction to commands from the remote control. Or the image appears immediately after turning on and disappears.
The most likely in these cases is a malfunction of the LED backlight. The reason may be a break in the LEDs, in the stabilization of their power supply, or in the violation of the contact connections of the thong connectors,
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the BN41-02528A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). If it is not possible to replace the MB board (SSB), you need to check the health of its elements - SDP1531, K4F8E304HBMGCH, 25Q40CLSIP, 25Q80DVSIG, S24C512C. Defective components should be replaced.
The malfunction of the tuner BN40-00323A is established after checking the software and all supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
Once again, remind users! Attempts to self-repair a SAMSUNG UE49MU6500U TV without the appropriate qualifications and necessary experience can lead to its complete non-repairability!


BN41-02528A
BN41-02528A can be used in TVs:
SAMSUNG UE43KU6650U (Panel CY-VK043HGAV5V), SAMSUNG UE43KU6000W UE43KU6000 (Panel CY-GK043HGEV1H), SAMSUNG UE55KU6400 UE55KU6400U (Panel CY-KK055HQLV4H), SAMSUNG UE49KU6670 UE49KU6670U (Panel CY-VK049HGLV4V), SAMSUNG UE40KU6000U (Panel LSF400FN05-L03 CY-GK040HGLV4V), SAMSUNG UE40KU6300U (Panel CY-WK040HGLV1V), SAMSUNG UE43KU6500U (Panel CY-VK043HGAV4V T430QVR01.0), SAMSUNG UE40KU6402U (Panel CY-KK040HGNV4H).
The appearance of the power supply
Main features of the SAMSUNG UE49MU6500U device:
Installed matrix (LED panel) CY-VK049HGLV4V.
To power the backlight LEDs, a converter is used, combined with a power supply.
The necessary supply voltages for all nodes of the SAMSUNG UE49MU6500U TV are generated by the BN44-00876D power module or its analogs using PFC, PWM microcircuits, and N-FET TO-220F type power switches.
MainBoard - the main board (motherboard) is a BN41-02528A module, using microchips SDP1531, K4F8E304HBMGCH, 25Q40CLSIP, 25Q80DVSIG, S24C512C and others.
The tuner BN40-00323A provides the reception of television programs and tuning to channels.