
SAMSUNG LED
Model: UE49MU7000U
Chassis / Version: FA01
Panel: CY-QK049FLLV3V
LED backlight: Edge LED 2 Strings
LED driver (backlight): integrated into PSU
Power Supply (PSU): BN44-00911A REV1.1 L55E8NR_MSM
PWM Power: PFC, PWM
MOSFET Power: N-FET TO-220F
MainBoard: BN41-02504A BN94-10753P
IC MainBoard: CPU, eMMC, DRAM, AUDIO, DC / DC
Tuner: One connect BN94-10924E
Technical Specifications UE49MU7000U
SAMSUNG UE49MU7000U
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE49MU7000U does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
In some of these cases, the main switching power supply, the BN44-00911A module, is faulty. It is necessary to verify the presence of its output voltages and, if they are completely absent, check the power switches (N-FET TO-220F) and rectifier diodes for a probable short circuit.
In case of breakdowns of semiconductors in the secondary circuits of any converter, as a rule, it can operate in emergency short circuit mode without output voltages, and during short circuit in the elements of the primary circuit, the mains fuse and, less often, the current sensor at the source of the key are most often cut off.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM, PWM, PWM microchips are usually checked by replacing with new ones, or obviously working.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
Often in such cases, there is no LED backlight. The reason may be a break in the LEDs, in the stabilization of their power supply, or in the violation of the contact connections of the strings
To check the LED lines for breaks without disassembling the panel, for example, a current source will help. It is impossible to open series-connected PN junctions with a simple multimeter, a voltage of the order of several tens of volts is required.
- The TV does not turn on, the indicator indicates standby or operating mode, or blinks.
Repair or diagnostics of the BN41-02504A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Often, the MB (SSB) card must be replaced in case of complex malfunctions that are difficult to detect. When trying to repair, you should check its elements - CPU, eMMC, DRAM, AUDIO, DC / DC and replace failed chips with new ones. Some malfunctions may be due to the use of BGA soldering technologies in modern Main Board technologies. Typically, such defects are detected by local heating of the chip.
The malfunction of the tuner One connect BN94-10924E is established after checking the software and all the supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
Attention! For users and owners of UE49MU7000U TVs who do not have the appropriate qualifications, knowledge and experience, we categorically do not recommend attempting self-repair in order to avoid negative consequences that could lead to complete non-serviceability of the device.


BN41-02504A
The appearance of the power supply
Main features of the SAMSUNG UE49MU7000U device:
Installed matrix (LED panel) CY-QK049FLLV3V.
To power the backlight LEDs, a converter is used, combined with a power supply.
The necessary supply voltages for all nodes of the SAMSUNG UE49MU7000U TV are generated by the BN44-00911A power module or its analogs using PFC, PWM microcircuits, and N-FET TO-220F type power switches.
MainBoard - the main board (motherboard) is a BN41-02504A module, using CPU, eMMC, DRAM, AUDIO, DC / DC, and others.
The One connect BN94-10924E tuner provides TV reception and channel tuning.