Technical description and composition of the SAMSUNG UE55ES6307 TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE55ES6307 UE55ES6307U
Panel: LTJ550HW08-L
LED backlight: 2012SVS55 7032NNB
LED driver (backlight): integrated into PSU
PWM LED driver: SLC5012M
Power Supply (PSU): BN44-00518B
PWM Power: FA5760N, SPC7011F (PFC)
MainBoard: BN41-01812A BN94-05857V
IC MainBoard: CPU: SEMS27; NAND FLASH KLM2G1HE3F-B001; EEPROM: 24C256; Submicom: WT61P805
Tuner: BN40-00239B
Control: Wi-Fi: WIBT30A BN96-21431C
Technical Specifications UE55ES6307
SAMSUNG UE55ES6307
General repair guidelines for TV LCD LED
Possible manifestations of defects
- SAMSUNG UE55ES6307 TV does not turn on, does not respond to the remote control and control panel buttons, indicators do not light up and do not blink.
Most likely in this case, the main switching power supply (IIP) BN44-00518B is faulty. It is necessary to measure its output voltages and, in case of their absence, check the serviceability of power switches and rectifier diodes in the converters for possible breakdown.
In the event of breakdowns in the secondary circuits of the converter, it can usually fail in short circuit mode, and in the event of a short circuit in the power elements of the primary circuit, the mains fuse or current sensor at the source of the key most often breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. Chips PWM (PWM) FA5760N, SPC7011F (PFC) are usually checked by replacing with new, or obviously working.
- There is no image, but there is sound, it reacts to the remote control. Or the image appears when you turn it on and immediately disappears
The most likely in these cases is a malfunction of the LED backlight. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the BN41-01812A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Complex repair of MB (SSB) is possible only in the conditions of a service center with the necessary equipment. Checking or replacing CPU elements: SEMS27; NAND FLASH KLM2G1HE3F-B001; EEPROM: 24C256; Submicom: WT61P805 requires the necessary training and professional skills to repair modules at the component level. Problems associated with the use of BGA soldering technologies can sometimes be diagnosed by warming up.
If you suspect a malfunction of the tuner BN40-00239B, first of all, you need to verify the correctness of the software, as well as the presence of the necessary voltage levels and pulses of data exchange with the processor via the I2C bus at the corresponding terminals of the tuner.
It should be remembered! Attempts to self-repair a SAMSUNG UE55ES6307 TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-repairability of the device!
The appearance of the MainBoard BN41-01812A is shown in the figure below:BN41-01812A
BN41-01812A can be used in TVs:
SAMSUNG UE32EH5300P (Panel DE320BGM-C1 ), SAMSUNG UE40ES6307U (Panel LTJ400HV05-L), SAMSUNG UE40ES5537K (Panel CY-LE400BGSV1L), SAMSUNG UE32ES5557K (Panel LE320BGM-C1), SAMSUNG UE40EH5307K (Panel LTJ400HM08-L), SAMSUNG UE37ES6307U (Panel LE370CSA-C1), SAMSUNG UE32ES5500 UE32ES5500W (Panel LE320BGM-C1), SAMSUNG UE32ES5530W UE32ES5530 (Panel LE320BGM-C1), SAMSUNG UE32ES5507K UE32ES5507V (Panel LE320BGM-C1), SAMSUNG UE32ES5537K (Panel LE320BGM-C1), SAMSUNG UE40ES5530W UE40ES5530 (Panel CY-LE400BGSV1L), SAMSUNG UE40ES6100W (Panel LTJ400HV05-L), SAMSUNG UE32EH5300W UE32EH5300 (Panel DE320BGM-C1), SAMSUNG UE32EH5307K UE32EH5307 (Panel DE320BGM-C1), SAMSUNG UE55ES6100W (Panel LTJ550HW08-L), SAMSUNG UE46ES6307U (Panel LTJ460HW05-L), SAMSUNG UE40EH5300W (Panel LTJ-400HM08-L), SAMSUNG UE46ES6100W UE46ES6100 (Panel LTJ460HW05-L), SAMSUNG UE37ES6100W (Panel LE370CSA-C1), SAMSUNG UE50ES5700 UE50ES5700SXZG (Panel LE500BGA-B2), SAMSUNG UE40ES5507K UE40ES5507 (Panel LE400BGA-B1), SAMSUNG UE46EH5300 UE46EH5300W (Panel LTJ460HN05-L), SAMSUNG UE32ES6307 UE32ES6307U (Panel LE320CSM-C1), SAMSUNG UE50ES5507K UE50ES5507 (Panel LE500BGA-B2), SAMSUNG UE40ES5557K UE40ES5557 (Panel LE400BGA-B1), SAMSUNG UE46ES6200 (Panel LTJ460HW05-C), SAMSUNG UE32ES6100 UE32ES6100W (Panel LE320CSM-C1), SAMSUNG UE40ES5500 UE40ES5500W (Panel LTJ400HM09-L), SAMSUNG UE32ES5550 UE32ES5550W (Panel LE320BGM-C1).
The appearance of the power supply
Main features of the SAMSUNG UE55ES6307 device:
Installed matrix (LED panel) LTJ550HW08-L.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by the SLC5012M PWM controller.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE55ES6307 TV is carried out by the BN44-00518B power module, or its analogs using the FA5760N, SPC7011F (PFC) microcircuits.
MainBoard - the main board (motherboard) is a BN41-01812A module, using CPU chips: SEMS27; NAND FLASH KLM2G1HE3F-B001; EEPROM: 24C256; Submicom: WT61P805 and others.
The tuner BN40-00239B provides the reception of television programs and tuning to channels.
