![](https://3.bp.blogspot.com/--yKw3SzIRIs/XihwsA6QiFI/AAAAAAAApG4/ti5kHspRdNM-TBVU4nAWukoXtff87VOlwCK4BGAYYCw/s200/UE55M6500.jpg)
SAMSUNG LED
Model: UE55M6500
Chassis / Version: CA01
Panel: CY-VK055BGHV1V
LED backlight: AOT SEC_55_FHD_1X72_7032C REV.V1 2016.04.29
T-CON: TT5461B07-1-C
LED driver (backlight): integrated into PSU
Power Supply (PSU): BN44-00872D L55E1K_KSM PSLF101S08B
MainBoard: BN41-02575B BN94-10502M
IC MainBoard: CPU: SDP1604
Tuner: BN40-00331B
Control: IR: A398028 BN41-02515A, Wi-Fi: WCM730Q BN59-01264A
Technical Specifications UE55M6500AU
SAMSUNG UE55M6500
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE55M6500 TV does not turn on. There are no signs of operability. The indicators on the front panel do not light or flash, the TV does not respond to the remote control and control buttons.
Most likely in this case, the main switching power supply (IIP) BN44-00872D is faulty. Then we recommend that you measure its output voltages and, if they are absent, you should check the health of the power switches and rectifier diodes of the converters for a probable short circuit.
In case of any breakdowns in the secondary circuits, the converter can operate in emergency short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse or the current sensor at the source of the key more often breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM), in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, there is sound, it responds to the remote control. Or the image may appear for a second when turned on and immediately disappears.
In some of these cases, the malfunction is caused by a lack of backlighting on the display. The reason can be both in the power of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To check the LED strips, to open all the transitions of the LEDs, several tens of volts or more are needed, it is best to use a current source for such purposes. The breakage of several PN junctions connected in series cannot be detected with a multimeter or tester. In such cases, it is necessary to open the panel and check each LED. If your multimeter cannot open the LED transitions in forward bias, sometimes you can detect the presence of a PN junction of the protective zener diode by connecting the probes in the opposite direction. If the zener diode is broken or broken in short-circuit, then the LED is faulty and needs to be replaced.
- The indicator blinks or lights constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the BN41-02575B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software).
If there is no reception of television channels, but the TV is working properly from external devices, first of all, check the voltage of the tuner BN40-00331B and update the software. The pulses from the I2C bus must be controlled with an oscilloscope.
It should be remembered! Attempts to self-repair a SAMSUNG UE55M6500 TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-serviceability of the device!
![](https://1.bp.blogspot.com/-AYIE7iIuugk/Xihw44gHJSI/AAAAAAAApHE/0RDGjslscKU5boWWAGCBq3IppC35gZBWACK4BGAYYCw/s320/BN41-02575B_DCE.jpg)
![](https://1.bp.blogspot.com/-Pcek3h5IZHA/Xihw5AmmIcI/AAAAAAAApHI/xEJF1aDSlnUFPl4BSUTqpkSJ5dofvYpOwCK4BGAYYCw/s320/BN44-00872D_DCE.jpg)
BN41-02575B
The appearance of the power supply
Main features of the SAMSUNG UE55M6500 device:
Installed matrix (LED panel) CY-VK055BGHV1V.
The matrix control uses the Timing Controller (T-CON) TT5461B07-1-C.
To power the backlight LEDs, a converter is used, combined with a power supply.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE55M6500 TV is carried out by the BN44-00872D power module, or its analogues.
MainBoard - the main board (motherboard) is a BN41-02575B module, using CPU chips: SDP1604 and others.
The tuner BN40-00331B provides the reception of television programs and tuning to channels.