Technical description and composition of the SAMSUNG UE65ES8005 TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE65ES8005
Chassis / Version: U81A
Panel: CY-LE650DSA V1C
T-CON: BN41-01790C
LED driver (backlight): integrated into PSU; 210V 203mA
Power Supply (PSU): BN44-00539A PD65B2Q_CHS
MainBoard: BN41-01800B BN94-05584R
IC MainBoard: RTL8201F; TAS5735; Si9587CNUC; SDP1101
Tuner: BN40-00238B
Technical Specifications UE65ES8005
SAMSUNG UE65ES8005
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE65ES8005 does not turn on and does not show any signs of performance at all. Does not blink indicators and does not respond to control buttons.
With such manifestations, the BN44-00539A power module usually fails. It is necessary to measure its output voltages, and in case of their absence (full or partial), it is necessary to check the serviceability of the power switches of the converters and rectifier diodes for the presence of a possible short circuit.
In case of diode breakdowns in the secondary circuits, the converter can operate in emergency short-circuit mode without output voltages, and during short circuit in the power elements of the primary circuit, the mains fuse and / or current sensor at the source of the key usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM), in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, but there is sound, it reacts to the remote control. Or the image appears when you turn it on and immediately disappears
As a rule, in such cases there is no display backlight. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
- The indicator blinks or lights constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the BN41-01800B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). In cases of attempts to repair the MB board (SSB), it is necessary to check the serviceability of its elements - RTL8201F; TAS5735; Si9587CNUC; SDP1101 which may require replacement with new ones. If a BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its conclusions with the board (it is diagnosed by heating).
If a tuner BN40-00238B is suspected of malfunction, first of all, it is necessary to verify the correctness of the software, as well as the presence of the necessary voltage levels and impulses of data exchange with the processor via the I2C bus at the corresponding terminals of the tuner.
Attention TV owners! Self-repair attempts by SAMSUNG UE65ES8005 are not recommended by the manufacturer and can lead to serious negative consequences!
SCHEMATIC MANUAL -------> SAMSUNG UE40ES80**, UE46ES80** UE55ES80** UE65ES80** CHASSIS U81A
The appearance of the MainBoard BN41-01800B is shown in the figure below:BN41-01800B
BN41-01800B can be used in TVs:
SAMSUNG UE40ES8007U UE40ES8007 (Panel LTJ400HL14-L), SAMSUNG UE40ES7507 UE40ES7507U (Panel LTJ400HL14-L), SAMSUNG UE65ES8005 (Panel CY-LE650DSA V1C).
The appearance of the power supply
Main features of the SAMSUNG UE65ES8005 device:
Installed matrix (LED panel) CY-LE650DSA V1C.
The matrix control uses the Timing Controller (T-CON) BN41-01790C.
To power the backlight LEDs, a converter is used, combined with a power supply.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE65ES8005 TV is carried out by the power module BN44-00539A, or its analogs.
MainBoard - the main board (motherboard) is a BN41-01800B module, using RTL8201F chips; TAS5735; Si9587CNUC; SDP1101 and others.
The tuner BN40-00238B provides the reception of television programs and tuning to channels.
