Technical description and composition of the HYUNDAI H-LED32V18 TV, type of panel and applicable modules. The composition of the modules.HYUNDAI LED
Model: H-LED32V18
Chassis / Version: TP.VST59.P83
Panel: CX315DLEDM T320XVN02.A
LED backlight: CX32071235A2
T-CON: T320XVN02.0 Ctrl BD
LED driver (backlight): integrated into MainBoard
PWM LED driver: OB3350CP
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6 LD7536 (6pin)
MOSFET Power: 7N60
MainBoard: TP.VST59.P83
IC MainBoard: CPU: TSUMV59XE, SPI FLASH: W25Q32BVS, AUDIO: TPA3110D2
Tuner: CDT-3NP5I1-10
Technical Specifications H-LED32V18T2
HYUNDAI H-LED32V18
General repair guidelines for TV LCD LED
Possible malfunctions
- The HYUNDAI H-LED32V18 TV does not turn on at all. The control lights do not light or flash. The TV on the remote control and the control panel buttons do not respond.
The malfunction in such cases, first of all, should be sought in the power elements of a switching power supply (IIP) - a network voltage converter (AC / DC), which in this TV model is combined with the MainBoard TP.VST59.P83 main board. It is necessary to measure its output voltages and, if they are absent, to check for short circuit probability in the converters power switches (7N60) and rectifier diodes.
In case of breakdowns of semiconductors in the secondary circuits, the converter can usually work abnormally in the short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse often breaks.
Breakdown of power switches (MosFet) in pulsed sources is sometimes caused by malfunctions of other circuit elements, for example, in circuits supplying a PWM controller, frequency-setting or damper ones, as well as in negative feedback (OOS) stabilization circuits. PWM controllers (PWM) PWM SOT23-6 LD7536 (6pin), if they do not have visible damage to the case and open short circuit between the terminals, are usually checked by replacement.
- There is no image, there is sound, it is responding to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
In such cases, the most likely malfunction of the LED backlight elements. The reason can be both in the power of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It is impossible to check the LED line for breaks without disassembling the panel with a multimeter or tester. For these purposes, it is necessary to open all series-connected PN junctions and a voltage of the order of tens of volts will be required, and ideally, a current source. Having disassembled the panel, it is necessary to check each LED separately. Chinese multimeters, as a rule, light up a single 3-volt LED in the forward direction. In the case of using dual 6-volt LEDs, the PN junction of its protective zener diode can serve as a health indicator. In faulty LEDs, the zener diode will either be cut off or broken into short-circuit.
- The indicator blinks or lights constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the TP.VST59.P83 motherboard should begin by checking the stabilizers and power converters needed to power the microcircuits and matrix. If necessary, update or replace the software (software). When repairing an MB board, you need to check its CPU components: TSUMV59XE, SPI FLASH: W25Q32BVS, AUDIO: TPA3110D2. Defective items should be replaced. If chips with BGA soldering technology are used, a problem in its implementation is detected by the local heating of the chip.
If you suspect a malfunction of the CDT-3NP5I1-10 tuner, first of all, it is necessary to verify the correctness of the software, as well as the presence of the necessary voltage levels and pulses of data exchange with the processor via the I2C bus at the corresponding terminals of the tuner.
Attention! Users and owners of H-LED32V18 TVs who do not have the appropriate qualifications, knowledge and experience are strongly discouraged from attempting self-repair in order to avoid negative consequences that could lead to complete non-repairability of the device.
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> Service manual and sсhematic diagram TP.VST59.P83
FIRMWARE FOR SPI FLASH -----------> HYUNDAI H-LED32V18, Main: TP.VST59.P83, Panel: CX315DLEDM T320XVN02.A
The appearance of MainBoard TP.VST59.P83 and voltage measurements at the test points are shown in the figure below:TP.VST59.P83
The TP.VST59.P83 motherboard is combined with a power module and is an independent device made on the basis of the TSUMV59Xxx multifunction processor. Repair of such a board must begin by checking the power batteries, as well as the operability of voltage converters and linear stabilizers, necessary to provide power to certain processor nodes, in particular: + 1.2V core power, built-in DDR + 1.8V memory and Stand- by 3.3V. The power supply voltage of the LCD panel is 5V or 12V, depending on the type of panel used, it is necessary to check directly on the LVDS connector.
TP.VST59.P83 can be used in TVs:
AKAI LEA-28A08W (Panel ST2751A01-1), ERISSON 39LEN52 (Panel TLV3931-02), ERISSON 32LEN52 (Panel TLV3231-01), FUSION FLTV-32L28B (Panel TH315B051-MD1), FUSION FLTV-39LF28B (Panel V390HJ1-P02), FUSION FLTV-32L41B (Panel DBMS315LK09-C), FUSION FLTV-40LF28B (Panel DBMS400LK01-A), HYUNDAI H-LED32V18 (Panel CX315DLEDM T320XVN02.A ), MYSTERY MTV-4023LW (Panel CX390DLEDM / T390HVN04.0), ROLSEN RL-39D1305F (Panel V390HJ1-P02 Rev. C1), RUBIN RB-32D3U (Panel T320XVN01.0), RUBIN RB-39D3F (Panel CX390DLEDM), SHIVAKI STV-40LED5 (Panel V390HJ1-P01 Rev C1), SUPRA STV-LC3225AWL (Panel TH315B051-MD2), SUPRA STV-LC32T810WL (Panel TC315F3E5-A), SUPRA STV-LC32880WL (Panel HE315GH-E77GM\PW1 ), SUPRA STV-LC2825WL (Panel SM275TC30), SUPRA STV-LC32820WL (Panel TC315FJE1-MD4), SUPRA STV-LC32810WL (Panel TC315F3E5-A), TELEFUNKEN TF-LED32S7 (Panel ST3151A05-5 CX315DLEDM).
Main features of the HYUNDAI H-LED32V18 device:
Installed matrix (LED-panel) CX315DLEDM T320XVN02.A.
The matrix control uses the Timing Controller (T-CON) T320XVN02.0.
To power the backlight LEDs, a converter is used, combined with the main board TP.VST59.P83, controlled by the OB3350CP PWM controller.
The power module is combined with the MainBoard and is made according to the scheme of a flyback AC / DC voltage converter using PWM SOT23-6 LD7536 microcircuits (6pin) and power switches of the 7N60 type.
MainBoard - the main board (motherboard) is a TP.VST59.P83 module, using CPU chips: TSUMV59XE, SPI FLASH: W25Q32BVS, AUDIO: TPA3110D2 and others.
The tuner CDT-3NP5I1-10 provides the reception of television programs and tuning to channels.
HYUNDAI H-LED32V18T2 TV with T320XVN02.A LCD, 32 "(81 cm) diagonal of 16: 9 format. The required screen brightness of 300 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 3000: 1. LED TV backlighting is implemented in the manufacturing technology of the screen of this TV model.High quality images can be viewed at 1366x768 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in . Tax PAL, SECAM, NTSC systems Image processing and the formation of the digital signal is in 480i standards, 480p, 576i, 576p, 720p, 1080i Supported multimedia file formats:. MP3, WMA, MPEG4, Xvid, DivX, MKV, JPEG.
The power of the sound system 20 W (2x10 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, RGB, VGA, HDMI x3, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768.
A digital tuner is capable of receiving television channels in the DVB-T, DVB-T2 standards.
Overall dimensions: with stand 750x510x200 mm, without stand 750x460x74 mm.
The mass of the TV: 8.9 kg.
Attention! The panel T320XVN02.A (CX315DLEDM) of an HYUNDAI H-LED32V18T2 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
