Technical description and composition of the HYUNDAI H-LED32V19 TV, panel type and applicable modules. The composition of the modules.HYUNDAI LED
Model: H-LED32V19
Chassis / Version: MS82PT
Panel: LVW320CSOT E45 V10
T-CON: MT3151A04-1-XC-9; I1142HS, P30Y / 1572, CS11102, P41J / 5562A
LED driver (backlight): integrated into MainBoard
PWM LED driver: OB3350CP
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6 LD7536R
MainBoard: TP.MS18VG.P77 / MS82PT
IC MainBoard: CPU: MST3M182VGC-LF-TZ, SPI FLASH: 25Q32, Audio: TPA3110LD2
Tuner: R620D
Control: IR: 40-HT3510-IRC2LG
Technical Specifications H-LED32V19
HYUNDAI H-LED32V19
General repair guidelines for TV LCD LED
Possible malfunctions
- HYUNDAI H-LED32V19 does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
The malfunction in such cases should be sought in the elements of the power source - the network voltage converter (AC / DC), which is located on the MainBoard TP.MS18VG.P77 main board. Then we recommend that you measure its output voltages and, if they are absent, you should check the health of the power switches and rectifier diodes of the converters for a probable short circuit.
In case of breakdowns in the secondary circuits, the converter, as a rule, can emergency work in the short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) PWM SOT23-6 LD7536R, in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, there is sound, it is responding to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
In most of these cases, a malfunction is detected in the nodes and backlight elements of the LED panel. The reason can be both in the power of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
When trying to detect a break in the LED lines, it should be taken into account that it is difficult to do this without disassembling the panel. For example, a current source is needed to open PN junctions connected in series.
- The TV does not turn on, the indicator indicates standby or operating mode, or blinks.
Repair or diagnostics of the TP.MS18VG.P77 motherboard should be started by checking the stabilizers and power converters needed to power the microcircuits and matrix. If necessary, update or replace the software (software). Board repair and replacement of CPU chips: MST3M182VGC-LF-TZ, SPI: 25Q32 are carried out with the necessary equipment, and the corresponding element base. Faults associated with the application of BGA processor soldering technologies can be localized by the heating method.
The failure of the NoName tuner is established after checking the software and all the supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
Attention! For users and owners of H-LED32V19 TVs who do not have the appropriate qualifications, knowledge and experience, we categorically do not recommend attempting self-repair in order to avoid negative consequences that could lead to complete non-repairability of the device.
FIRMWARE FOR SPI FLASH -----------> HYUNDAI H-LED32V19, Main: TP.MS18VG.P77 /MS82PT, Panel: LVW320CSOT E45 V10
FIRMWARE FOR SPI FLASH -----------> HYUNDAI H-LED32V19, Main: TP.MS18VG.P77 , Panel: LVW320CSOT E45 V10
The appearance of MainBoard TP.MS18VG.P77 is shown in the figure below:TP.MS18VG.P77
TP.MS18VG.P77 can be used in TVs:
ERISSON 24LET35 (Panel LVW240CMOT E1 V2), ERISSON 19LET35 (Panel M185XTN01.3), FUSION FLTV-24C10 (Panel LVW230SSOT E1 V2), FUSION FLTV-32C10 (Panel LVW320CSOT E81 V7), HYUNDAI H-LED32V19 (Panel LVW320CSOT E45 V10), HYUNDAI H-LED32V23 (Panel LVW320C80T E64 V5), TCL 19T2100 (Panel M185XTN01.2), TELEFUNKEN TF-LED32S23 (Panel LVW320CS0T E146 V1), THOMSON 32B2600 (Panel LVW320C8OT EB1), THOMSON 28B2500 (Panel LVW280CSOT E13V1).
Main features of the HYUNDAI H-LED32V19 device:
Installed matrix (LED-panel) LVW320CSOT E45 V10.
The matrix control uses the Timing Controller (T-CON) MT3151A04-1-XC-9 ;.
To power the backlight LEDs, a converter is used, combined with the main board TP.MS18VG.P77, controlled by the OB3350CP PWM controller.
The power module is combined with the MainBoard and is designed according to a flyback AC / DC voltage converter using PWM SOT23-6 LD7536R microcircuits.
MainBoard - the main board (motherboard) is a TP.MS18VG.P77 module, using CPU chips: MST3M182VGC-LF-TZ, SPI FLASH: 25Q32, Audio: TPA3110LD2 and others.
The R620D tuner provides TV reception and channel tuning.
HYUNDAI H-LED32V19 TV with LVW320CSOT LCD display, 32 "(81 cm) diagonal size in 16: 9 format. The required screen brightness of 300 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 3000: 1. Edge LED backlighting is realized in the LED-panel of this TV - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems . Max PAL, SECAM, NTSC Image processing and the formation of the digital signal is in 480i standards, 480p, 576i, 576p, 720p, 1080i, 1080p Supported multimedia file formats:. MP3, WMA, MPEG4, Xvid, DivX, MKV, JPEG.
The power of the sound system 10 W (2x5 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, VGA. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768, 1920x1080.
Overall dimensions: 733x502x180 mm.
TV Weight: 7.5 kg.
Attention! The panel of the LVW320CSOT E45 V10 of the HYUNDAI H-LED32V19 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
