Technical description and composition of the HYUNDAI H-LED32V23 TV, panel type and applicable modules. The composition of the modules.HYUNDAI LED
Model: H-LED32V23
Chassis / Version: TP.MS18VG.P77
Panel: LVW320C80T E64 V5
LED driver (backlight): integrated into MainBoard
PWM LED driver: OB3350CP
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6 LD7536R
MainBoard: TP.MS18VG.P77
IC MainBoard: CPU: MST3M182VGC-LF-TZ, SPI FLASH: 25Q32, Audio: TPA3110LD2
Tuner: R620D
Technical Specifications H-LED32V23
HYUNDAI H-LED32V23
General repair guidelines for TV LCD LED
Possible manifestations of defects
- The HYUNDAI H-LED32V23 TV does not turn on. There are no signs of operability. The indicators on the front panel do not light or flash, the TV does not respond to the remote control and control buttons.
First of all, in such cases, you should verify the operability of the common switching power supply (IIP) - AC / DC voltage converter of the mains voltage. All source elements in this TV model are located on the MainBoard TP.MS18VG.P77 main board. Then it is necessary to measure its output voltages and, in case of their complete or partial absence, it is necessary to check the serviceability of power switches and rectifier diodes of the converters for a possible short circuit.
In case of diode breakdowns in the secondary circuits, the converter can operate in emergency short-circuit mode without output voltages, and during short circuit in the power elements of the primary circuit, the mains fuse and / or current sensor at the source of the key usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) PWM SOT23-6 LD7536R, in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, there is sound, it responds to the remote control, the channels are switched. In some cases, the image appears when you turn on and immediately disappears.
As a rule, in such cases there is no display backlight. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
When diagnosing, it is necessary to take into account that it is impossible to check the open in the chain of LED lines without disassembling the panels using a tester or multimeter. To open all PN junctions connected in series, a voltage of the order of several tens of volts is required, and ideally, a current source. By opening the panel, each LED can be checked separately. Typically, Chinese multimeters light up a single 3-volt LED, if you connect probes in the forward direction to it. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of health. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights constantly or blinks.
Repair or diagnostics of the TP.MS18VG.P77 motherboard should be started by checking the stabilizers and power converters needed to power the microcircuits and matrix. If necessary, update or replace the software (software). If it is not possible to replace the MB (SSB) card, you need to check the health of its elements - CPU: MST3M182VGC-LF-TZ, SPI FLASH: 25Q32, Audio: TPA3110LD2. Defective components should be replaced.
In cases where there is no tuning to the channels of on-air or cable television, you should make sure that the software is correct, as well as in accordance with the ratings of the supply voltage at the terminals of the NoName tuner. It is also necessary to check the presence of pulses of data exchange between the tuner and the processor via the I2C bus using an oscilloscope.
It should be remembered! Attempts to independently repair the HYUNDAI H-LED32V23 TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-serviceability of the device!
FIRMWARE FOR SPI FLASH -----------> HYUNDAI H-LED32V23, Main: TP.MS18VG.P77, Panel: LVW320C80T E64 V5
The appearance of MainBoard TP.MS18VG.P77 is shown in the figure below:TP.MS18VG.P77
TP.MS18VG.P77 can be used in TVs:
ERISSON 24LET35 (Panel LVW240CMOT E1 V2), ERISSON 19LET35 (Panel M185XTN01.3), FUSION FLTV-24C10 (Panel LVW230SSOT E1 V2), FUSION FLTV-32C10 (Panel LVW320CSOT E81 V7), HYUNDAI H-LED32V19 (Panel LVW320CSOT E45 V10), HYUNDAI H-LED32V23 (Panel LVW320C80T E64 V5), TCL 19T2100 (Panel M185XTN01.2), TELEFUNKEN TF-LED32S23 (Panel LVW320CS0T E146 V1), THOMSON 32B2600 (Panel LVW320C8OT EB1), THOMSON 28B2500 (Panel LVW280CSOT E13V1).
Main features of the HYUNDAI H-LED32V23 device:
Installed matrix (LED-panel) LVW320C80T E64 V5.
To power the backlight LEDs, a converter is used, combined with the main board TP.MS18VG.P77, controlled by the OB3350CP PWM controller.
The power module is combined with the MainBoard and is designed according to a flyback AC / DC voltage converter using PWM SOT23-6 LD7536R microcircuits.
MainBoard - the main board (motherboard) is a TP.MS18VG.P77 module, using CPU chips: MST3M182VGC-LF-TZ, SPI FLASH: 25Q32, Audio: TPA3110LD2 and others.
The R620D tuner provides TV reception and channel tuning.
HYUNDAI H-LED32V23 TV with LVW320C80T LCD display, 32 "(81 cm) diagonal size in 16: 9 format. The required screen brightness of 320 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 3000: 1. Edge LED backlighting is realized in the LED-panel of this TV - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems . Max PAL, SECAM, NTSC Image processing and the formation of the digital signal is in 480i standards, 480p, 576i, 576p, 720p, 1080i Supported multimedia file formats:. MP3, WMA, MPEG4, Xvid, DivX, MKV, JPEG.
The power of the sound system 10 W (2x5 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, VGA, HDMI, USB. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
Overall dimensions: 740x500x191 mm.
TV mass: 6 kg.
Attention! The panel of the LVW320C80T E64 V5 LED-TV HYUNDAI H-LED32V23 is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
