Technical description and composition of the TOSHIBA 32RL933RB TV, type of panel and applicable modules. The composition of the modules.TOSHIBA LED
Model: 32RL933RB
Panel: LTA320HN03 T03
LED backlight: LJ64-03204A 2 * 36 led
LED driver (backlight): SSL320 3E2B Rev0.0
PWM LED driver: SSL100SN
MOSFET LED driver: STA3250, APM4015P, SF10A400HD
Trans LED driver: KL-04012301A-KD
Power Supply (PSU): DPS-115EP A
PWM Power: A6069H (7), 1608B (PFC), DDA014 (18)
MainBoard: PE1070 E V28A00140701
IC MainBoard: CPU: MSD381USV-V6; DRAM: K4B1G1646G-BCK0; NAND Flash: TC58NVG1S3E; SPI Flash: MX25L1606EM2I-12G
Tuner: ENGS7305D5F
Control: CT-90404
Specifications 32RL933
TOSHIBA 32RL933RB
General repair guidelines for TV LCD LED
It is advisable to start the repair of the TOSHIBA 32RL933RB TV with a careful external examination of both internal and external elements. According to some external signs of a change in the state of some elements, it is sometimes possible to make assumptions about the nature of the defect, as well as determine the further direction of the troubleshooting. Carbonized paint on the upper layer of resistors, electrolytic capacitors of rectifier filters swollen after boiling, cracked soldering at the terminals of heating elements or transformers can often suggest the cause of the defect and possible consequences.
If the power supply module DPS-115EP A fails, the external manifestations may be different, for example, the TOSHIBA 32RL933RB does not turn on at all and there is no indication of the indicator lights on the front panel. With the same symptoms, the stabilizer (converter) of the power supply to the control processor may be faulty. It is advisable to start the troubleshooting of the power supply module by checking the state of the electrolytic capacitors of the rectifier filters and the mains fuse. Defective capacitors should be replaced. If the mains fuse is broken, it is necessary to check first of all the power semiconductor elements - rectifier diodes and transistors, which are often found in such a state of breakdown.
Power switches in pulsed power supplies (SMPS) fail extremely rarely for no reason and, if they are broken, it is necessary to look for a malfunction in the stabilization circuits by checking electrolytic capacitors, semiconductor devices, and resistors in the primary circuit. The reason may be a malfunction of the PWM controller chip A6069H (7), 1608B (8), DDA014 (18), which can only be checked by replacing it with a new or obviously working one.
If the TOSHIBA 32RL933RB does not have an image, but there is sound and the TV is controlled from the remote control, a malfunction in the backlight circuits of the LTA320HN03 T03 panel is likely. The LEDs or the power converter - LED driver may be faulty. Often in such cases, when you turn on the TV, an image appears and immediately disappears. First of all, it is necessary to verify the operability of the electrolytic capacitors of the rectifier filter supplying the LED driver, and check the LEDs, connecting obviously known good diagnostics.
To check the health of the LEDs, as well as contact connections in the ruler circuit, it is necessary to disassemble the panel.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
The motherboard PE1070 E V28A00140701 must be checked if there is no reaction to the remote control and function buttons, the standby indicator blinks or lights up continuously. In such cases, if the converters or power regulators of the microcircuit are working, a software update may be necessary.
Remember! Attempts by users to repair the TOSHIBA 32RL933RB TV without proper qualifications and the necessary experience can lead to serious negative consequences!
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> Toshiba - 23RL933RB, 32RL933RB, 40RL933RB , 23RL953RB, 32RL953RB, 40RL953RB. Main PE1070
Service Manuals with Schematic Diagrams 134 pages 2012 ------------------>32TL933, 40TL933, 46TL933, 32TL936, 40TL936, 46TL936, 32TL963, 40TL963, 46TL963, 32TL966, 40TL966, 46TL966, 32UL975, 40UL975, 46UL975, 23RL933, 32RL933, 40RL933, 23RL936, 32RL936, 40RL936, 23SL970, 32SL970, 40SL970, 32RL953, 40RL953, 42VL963, 47VL963, 55VL963, 42XL975, 47XL975, 55XL975, 40ML933, 46ML933
The appearance of the MainBoard PE1070 is shown in the figure below:PE1070
PE1070 can be used in TVs:
TOSHIBA 23RL933RB (Panel LC230EUE SE A1), TOSHIBA 32RL933RB (Panel LTA320HN03 T03), TOSHIBA 32RL955RB (Panel LTA320HN03 T03), TOSHIBA 40RL955RB (Panel LTA400HM22 T03), TOSHIBA 32RL953RB (Panel LTA320HN03), TOSHIBA 40RL933RB (Panel LTA400HM22 LJ96-06007A).
PSU Advanced
The DPS-115EP power module is designed using a Power Factor Correction (PFC) scheme to eliminate multiple AC harmonics introduced into the power supply by the device. The PFC node is a Step-Up Converter based on a 1608B PWM controller that evenly distributes high-frequency impulses of the charging current of the electrolytic capacitor of the rectifier filter of the mains voltage over a period of 50 Hz. The current of its charge in this case will already be determined not by its reactance (usually 10-30 ohms for the network frequency), but by the elements of the converter. As a result, a change in the amplitude of the pulses (envelope) of the consumed current of the converter will repeat the shape and phase of the input sinusoidal voltage. The availability of an increased voltage (about + 380V) in the operating mode on the capacitor of the line filter indicates the serviceability of the PFC node.
The appearance of the power supply
Main features of the TOSHIBA 32RL933RB device:
Installed matrix (LED panel) LTA320HN03 T03.
To power the backlight LEDs, the SSL320 LED driver is used, it is controlled by the SSL100SN PWM controller. A transformer KL-04012301A-KD is installed in the LED driver converter. As the power elements of the LED driver, keys of the type STA3250, APM4015P, SF10A400HD are used.
The necessary supply voltages for all nodes of the TOSHIBA 32RL933RB TV are generated by the DPS-115EP power supply module or its analogs using A6069H (7), 1608B (PFC), DDA014 (18) microcircuits.
MainBoard - the main board (motherboard) is a PE1070 module, using CPU chips: MSD381USV-V6; DRAM: K4B1G1646G-BCK0; NAND Flash: TC58NVG1S3E; SPI Flash: MX25L1606EM2I-12G and others.
The ENGS7305D5F tuner provides TV reception and channel tuning.
Additional technical information about the panel:
Brand: SAMSUNG
Model: LTA320HN03-T
Type: a-Si TFT-LCD, Panel
Diagonal size: 31.5 inch
Resolution: 1920x1080, FHD
Display Mode: S-PVA, Normally Black, Transmissive
Active Area: 698.4x392.85 mm
Surface: Antiglare (Haze 5.5%)
Brightness: 400 cd / m²
Contrast Ratio: 5000: 1
Display Colors: 1.07B (10-bit), CIE1931 70%
Response Time: 16 (Max.) (Tr + Td)
Frequency: 60Hz
Lamp Type: WLED Embedded (LED Driver)
Signal Interface: LVDS (2 ch, 10-bit), 51 pins
Voltage: 12.0V
TOSHIBA 32RL933 LED TV with LTA320HN03 LCD display, 32 "(81 cm) diagonal size in 16: 9 format. The required screen brightness of 400 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 1,000,000: 1 is achieved by special control of the LEDs. V This model uses side illumination from Edge LEDs.The design and technical capabilities of the TV include viewing programs and movies in high quality HD at a resolution of 1920x1080 pixels in a graphical resolution according to the standard 1080p (Full HD).
The 32RL933 is equipped with SMART software, integrated applications and the ability to work on the Internet. Connecting to the Internet can be done via Wi-Fi. The input high-frequency or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats: MP3, WMA, MPEG4, Xvid, DivX, MKV, JPEG.
The power of the sound system 20 W (2x10 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, SCART, RGB, VGA, HDMI x3, USB, Ethernet (RJ-45), WiDi. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768, 1920x1080.
A digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C standards.
The power consumed by the TV in the operating mode from the network is 71 watts.
Overall dimensions: with stand 735x506x207 mm, without stand 735x449x56 mm.
TV mass: with stand: 9.5 kg, without stand: 8.2 kg.
Attention! The LTA320HN03 T03 panel of the TOSHIBA 32RL933 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
