Technical description and composition of the GOLDSTAR LD-19A300R TV, panel type and modules used. The composition of the modules.GoldStar LED
Model: LD-19A300R
Chassis / Version: V2L12
Panel: V185B1-PE1
LED backlight: EDGE LED
LED driver (backlight): 12V LED-DRIVER
PWM LED driver: OB3362RP
Power Supply (PSU): Adapter 12V
MainBoard: T.VST29.61C 12296
IC MainBoard: CPU: TSUMV59XE-Z1, SPI FLASH: EN25Q32B, AUDIO: YD1517P
Tuner: CDT-3SP512-36
Specifications LD-19A300R
GOLDSTAR LD-19A300R
General recommendations for TV LCD LED repair
Possible manifestations of malfunctions
- TV GoldStar LD-19A300R does not turn on at all. Control lamps do not light up or blink. The TV on the remote control and control panel buttons does not respond.
With such manifestations, the adapter power supply usually fails.
This TV model is equipped with an external adapter 12V type power supply, which the owner can purchase on his own, and its repair may not always be advisable, however, sometimes it makes some sense to open it and eliminate simple typical defects typical for SMPS. Its output voltages should be measured and, in their absence, the power switches and rectifier diodes should be checked for the probability of a short circuit in the converters.
In case of breakdowns of semiconductors in the secondary circuits, the converter can usually work in an emergency in the short-circuit mode, and with a short circuit in the power elements of the primary circuit, the mains fuse often breaks.
Mos-Fet power switches used in switching power supplies sometimes fail due to a malfunction of any other elements that can disable it in the key mode, or create an excess of the maximum permissible key parameters. These can be elements supplying a PWM regulator, frequency setting or damper circuits, or elements of negative feedback in the stabilization circuit. PWM controllers, in the absence of visible damage or outright short circuits between the terminals, are checked by replacing them with new ones, or knowingly working properly.
- There is no picture, but there is sound and reaction to the remote control. Or, for a second, the image may appear immediately after switching on.
Usually, in such cases, a malfunction is detected in the LED panel backlight nodes. The reason may be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
When trying to detect a break in the LED lines, it should be borne in mind that it is difficult to do this without disassembling the panel. For example, a current source is required to open PN junctions connected in series.
- The indicator blinks or is on constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the T.VST29.61C motherboard should begin with checking the stabilizers and power converters required to power the microcircuits and matrix. If necessary, you should update or replace the software (software). If it is not possible to replace the MB (SSB) board, it is necessary to check the serviceability of its elements - CPU: TSUMV59XE-Z1, SPI FLASH: EN25Q32B, AUDIO: YD1517P. Defective components must be replaced.
If the TV operates normally from external devices, but does not tune to TV channels, the CDT-3SP512-36 tuner may be faulty. In such cases, first of all, you should make sure that there are supply voltages at its corresponding terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the reason for the inoperability of the tuner may be a software failure.
Owners of the LD-19A300R TV are advised to contact only qualified specialists with the necessary work experience for repair! Attempts to repair yourself without the appropriate knowledge and skills can lead to irreversible negative consequences!
DOWNLOAD FIRMWARE FOR SPI FLASH -----------> GoldStar LD-19A300R V2L12, Main: T.VST29.61C 12296, Panel: V185B1-PE1
To reduce the backlight current in LED drivers with OB3362RP (TSOP16) controller, increase the total resistance of the resistors from pin 5 (ISET) to the case. The maximum current in each of the four channels (in milliamperes) for the Rset resistor (in kilo-ohms) is determined from the ratio 3000 * 1.2V / Rset.
Additional MainBoard RepairThe appearance of the MainBoard T.VST29.61C is shown in the figure below:
T.VST29.61C
T.VST29.61C can be used in TVs:
GOLDSTAR LT-24A300F (Panel M236HGE-P01), GoldStar LD-19A300R (Panel V185B1-PE1), SUPRA STV-LC19410WL (Panel M185BGE-P02 HK185WLEDM-CH15H), SUPRA STV-LC2277FL (Panel LM215DA-T01), SUPRA STV-LC22410WL (Panel LM216DA-T01), SUPRA STV-LC24410FL (Panel M236H1-P01 HK236WLEDM-CH84H ).
Main features of the GOLDSTAR LD-19A300R device:
Installed matrix (LED panel) V185B1-PE1.
To power the backlight LEDs, a 12V LED driver is used, controlled by the OB3362RP PWM controller.
To power all internal components of the GOLDSTAR LD-19A300R TV, an external adapter 12V is used.
MainBoard - the main board (motherboard) is a T.VST29.61C module, using CPU chips: TSUMV59XE-Z1, SPI FLASH: EN25Q32B, AUDIO: YD1517P and others.
The CDT-3SP512-36 tuner provides reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: CMO
Model: V185B1-PE1
Type: a-Si TFT-LCD, CELL
Diagonal size: 18.5 inch
Resolution: 1366x768, WXGA
Display Mode: TN, Normally White, Transmissive
Active Area: 409.8x230.4 mm
Surface: Antiglare (Haze 25%), Hard coating (3H)
Glass Depth: 0.70 + 0.70 mm
Transmissivity: 6.0% (with Polarizer)
Contrast Ratio: 1000: 1
Display Colors: 16.7M (8-bit)
Response Time: 1.3 / 3.7 (Tr / Td)
Frequency: 60Hz
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 5.0V ..........................
GOLDSTAR LD-19A300R TV with LCD V185B1-PE1, 19 "(48 cm) diagonal, 16: 9 format. The required screen brightness of 250 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 60,000: 1 is achieved by special control of LED operation The technology of production of the screen of this TV model is realized with LED backlighting.It is possible to view images in high quality HD at a resolution of 1366x768 pixels in the standard graphic resolution 720p (HD Ready) .Input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal shaping takes place in the standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p Supported multimedia file formats: MP3, WMA, MPEG4, MKV, Picture CD, JPEG.
Speaker power 6 W (2x3 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, VGA, HDMI, USB. A headphone output is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector on the TV case is used, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
The power consumed by the TV operating in mains mode is 30 W.
Overall dimensions: 454x337x155 mm.
TV weight: 3.05 kg.
Attention! Panel V185B1-PE1 of LED TV GOLDSTAR LD-19A300R is an expensive and unreliable element.
Do not allow any impact on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.
