SAMSUNG LED
Model: UE46ES6100W UE46ES6100
Panel: LTJ460HW05-L
T-CON: LSJ460HW05-S BN95-00578A
LED driver (backlight): integrated into PSU
PWM LED driver: SLC5012M = MAP3312B
Power Supply (PSU): BN44-00518B PD46B1D_CHS
PWM Power: FA5760N, SPC7011F
MainBoard: BN41-01812A BN94-06898B
IC MainBoard: CPU: SEMS27; SDRAM: K4B2G1646C-HCK0; NAND FLASH: KLM2G1HE3F-B001; EEPROM: 24C256
Tuner: DTDO40FSVL084AA BN40-00232A
Appearance
SAMSUNG UE46ES6100W
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE46ES6100W TV does not turn on at all. There is no reaction to the remote control and control buttons from the front panel. Indicator lights do not light or flash.
With such manifestations, in most cases, the BN44-00518B power module is faulty. It is necessary to measure the output voltages in the secondary circuits, and in case of their absence, check the serviceability of the power switches of the converters and rectifier diodes for a possible breakdown (short circuit).
In the event of breakdowns in the secondary circuits of the converter, it can usually fail in short circuit mode, and in the event of a short circuit in the power elements of the primary circuit, the mains fuse or current sensor at the source of the key most often breaks.
Mos-Fet power switches used in switching power supplies sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible key parameters. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PWM controllers FA5760N, SPC7011F, in the absence of visible damage or frank short-circuit between the terminals, are checked by replacing with new, or obviously working.
- There is no image, but there is sound and reaction to commands from the remote control. Or the image appears immediately after turning on and disappears.
Usually in such cases, a malfunction is detected in the backlight nodes of the LED panel. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To check the LED lines for breaks without disassembling the panel, for example, a current source will help. It is impossible to open series-connected PN-junctions with a simple multimeter, a voltage of the order of several tens of volts is required.
- The TV does not turn on, the indicator signals standby or working mode, or blinks.
Repair or diagnostics of the BN41-01812A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its CPU chips: SEMS27; SDRAM: K4B2G1646C-HCK0; NAND FLASH: KLM2G1HE3F-B001; EEPROM: 24C256 and other possible defective components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
If there is no reception of television channels, but the TV works properly from external devices, first of all, check the voltage of the tuner DTDO40FSVL084AA BN40-00232A and update the software. The pulses from the I2C bus must be controlled with an oscilloscope.
Owners and users of the SAMSUNG UE46ES6100W TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
SCHEMATIC ---------------> Power supply BN44-00520C.
SCHEMATIC MANUAL --------------------> SAMSUNG Chassis U78A/U79A Model: UE**ES61***, UE**ES63***, UE**ES65***, UE**ES67***, UE**ES68***.
The appearance of the MainBoard BN41-01812A is shown in the figure below:
BN41-01812A
BN41-01812A can be used in TVs:
SAMSUNG UE32EH5300P (Panel DE320BGM-C1 ), SAMSUNG UE40ES6307U (Panel LTJ400HV05-L), SAMSUNG UE40ES5537K (Panel CY-LE400BGSV1L), SAMSUNG UE32ES5557K (Panel LE320BGM-C1), SAMSUNG UE40EH5307K (Panel LTJ400HM08-L), SAMSUNG UE37ES6307U (Panel LE370CSA-C1), SAMSUNG UE32ES5500 UE32ES5500W (Panel LE320BGM-C1), SAMSUNG UE32ES5530W UE32ES5530 (Panel LE320BGM-C1), SAMSUNG UE32ES5507K UE32ES5507V (Panel LE320BGM-C1), SAMSUNG UE32ES5537K (Panel LE320BGM-C1), SAMSUNG UE40ES5530W UE40ES5530 (Panel CY-LE400BGSV1L), SAMSUNG UE40ES6100W (Panel LTJ400HV05-L), SAMSUNG UE32EH5300W UE32EH5300 (Panel DE320BGM-C1), SAMSUNG UE32EH5307K UE32EH5307 (Panel DE320BGM-C1), SAMSUNG UE55ES6100W (Panel LTJ550HW08-L), SAMSUNG UE46ES6307U (Panel LTJ460HW05-L), SAMSUNG UE40EH5300W (Panel LTJ-400HM08-L), SAMSUNG UE46ES6100W UE46ES6100 (Panel LTJ460HW05-L), SAMSUNG UE37ES6100W (Panel LE370CSA-C1), SAMSUNG UE50ES5700 UE50ES5700SXZG (Panel LE500BGA-B2), SAMSUNG UE40ES5507K UE40ES5507 (Panel LE400BGA-B1), SAMSUNG UE46EH5300 UE46EH5300W (Panel LTJ460HN05-L), SAMSUNG UE32ES6307 UE32ES6307U (Panel LE320CSM-C1), SAMSUNG UE50ES5507K UE50ES5507 (Panel LE500BGA-B2), SAMSUNG UE40ES5557K UE40ES5557 (Panel LE400BGA-B1), SAMSUNG UE46ES6200 (Panel LTJ460HW05-C), SAMSUNG UE32ES6100 UE32ES6100W (Panel LE320CSM-C1), SAMSUNG UE40ES5500 UE40ES5500W (Panel LTJ400HM09-L), SAMSUNG UE32ES5550 UE32ES5550W (Panel LE320BGM-C1).
The appearance of the power supply
Main features of the SAMSUNG UE46ES6100W device:
Installed matrix (LED-panel) LTJ460HW05-L.
The matrix control uses the Timing Controller (T-CON) LSJ460HW05-S.
To power the backlight LEDs, a converter is used, combined with a power supply unit, controlled by the PWM controller SLC5012M = MAP3312B.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE46ES6100W TV is carried out by the BN44-00518B power module, or its analogs using FA5760N, SPC7011F microcircuits.
MainBoard - the main board (motherboard) is a BN41-01812A module, using CPU chips: SEMS27; SDRAM: K4B2G1646C-HCK0; NAND FLASH: KLM2G1HE3F-B001; EEPROM: 24C256 and others.
The tuner DTDO40FSVL084AA BN40-00232A provides the reception of television programs and tuning to channels.