
SAMSUNG LED
Model: UE50J6240 UE50J6240AU
Chassis / Version: Ver: DA01
Panel: CY-GH050CSNV4V
LED backlight: D4GE-500DCA-R2 (14.03.17)
T-CON: 2015_INX_FHD_HAWK_FTS_V04
LED driver (backlight): integrated into PSU
Power Supply (PSU): BN44-00704E
PWM Power: FA6A01
MainBoard: BN41-02353C BN94-10814C
IC MainBoard: W25Q40, 24c512
Control: BN59-01198Q, WIFI: WIDT30Q BN59-01174D
Technical Specifications UE50J6240AU
SAMSUNG UE50J6240
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE50J6240 TV does not turn on at all. The control lights do not light or flash. On the remote control and the buttons on the control panel does not respond.
In such cases, the BN44-00704E power supply is usually faulty. It is necessary to measure the secondary output supply voltages, and in case of their absence, check the serviceability of the power switches of the converters and rectifier diodes for the possibility of breakdown in PN semiconductor junctions.
During thermal and avalanche breakdowns of semiconductors in secondary circuits, the converter can usually work normally in emergency short circuit mode. There are no output voltages. And with a short circuit in the power elements of the primary circuit, as a rule, the mains fuse breaks and less often the current sensor at the source of the key.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, power supply, frequency-setting, damper ... as well as elements of the Negative Stabilization Feedback. The PWM chip FA6A01 can also cause a malfunction of the power switch of the converter and is checked by replacement.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
In most of these cases, a malfunction is detected in the nodes and backlight elements of the LED panel. The reason can be both in the power of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It is impossible to check the line of series-connected LEDs without a special current source, and for this purpose it is not safe to use any voltage sources above 12V for them. Then it remains only to open the panel and check each LED separately. Usually, Chinese 9V-powered multimeters light up a single 3-volt LED, if you connect the probes in the forward direction, the red probe to the anode, and the black to the cathode. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of health. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the BN41-02353C motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Sophisticated MB board repair (SSB) is in some cases possible and practiced by repairmen. To do this, check and, if necessary, replace the elements W25Q40, 24c512. BGA chip malfunctions are usually easy to detect by warming up.
Attention to users! Self-repair of a SAMSUNG UE50J6240 TV without the appropriate qualifications and necessary experience can lead to its complete non-repairability!

BN41-02353C
BN41-02353C can be used in TVs:
SAMSUNG UE50J6240 UE50J6240AU (Panel CY-GH050CSNV4V), SAMSUNG UE40J6230AU (Panel CY-GH040BGLVBV), SAMSUNG UE40J6240AU (Panel CY-GH040BGLVBV).
The appearance of the power supply
Main features of the SAMSUNG UE50J6240 device:
Installed matrix (LED panel) CY-GH050CSNV4V.
The matrix control uses the Timing Controller (T-CON) 2015_INX_FHD_HAWK_FTS_V04.
To power the backlight LEDs, a converter is used, combined with a power supply.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE50J6240 TV is carried out by the BN44-00704E power module, or its analogs using FA6A01 microcircuits.
MainBoard - the main board (motherboard) is a BN41-02353C module, using W25Q40, 24c512 chips and others.